Difference between revisions of "Autonomous Underwater Vehicle"
(92 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
=Technology Roadmap Sections and Deliverables= | |||
The unique identifier of this technology roadmap is: | |||
* '''2AUVOPI - Autonomous Underwater Vehicle for Offshore Platform Inspection''' | |||
This indicates that we are dealing with a “level 2” roadmap at the product or system level, where “level 1” would indicate a market level roadmap and “level 3” or “level 4” would indicate an individual technology roadmap. | |||
==Roadmap Overview== | ==Roadmap Overview== | ||
The offshore platforms are the oil and gas production facilities that are located offshore. In the past, oil and gas were generally produced on the ground. However, as the number of fossil fuel-rich sites that were accessible from the ground has been limited, offshore oil and gas development has been important. In 2016, there were more than 3,000 offshore oil and gas production facilities in the world, and it is estimated that the number of facilities will increase.<ref>International Energy Agency (IEA), Offshore Energy Outlook (2018), https://webstore.iea.org/download/direct/1034</ref><br> | |||
The offshore platform has a lot of subsea structures such as pipelines, so the inspection and maintenance of these structures is a very important issue. However, some platforms are installed in water depths of more than hundreds of meters, so it is impossible for humans to dive and inspect these structures. In order to overcome this problem, Remotely Operated Vehicles (ROVs) are widely used. ROVs are unmanned vehicles that are connected to the mothership by a wire and can be manipulated by operators who are boarding in the mothership. In addition, ROVs can get power through the wire, so they can be operated for a long time. However, ROVs have many problems such as motion limitation caused by the wire.<br> | |||
On the other hand, the Autonomous Underwater Vehicles (AUVs) don't have wires, so the operation flexibility is the great advantage of AUVs. In order to take advantage of this strength of flexibility, securing the accuracy of position sensing is important for AUVs. Meanwhile, the capacity limit of the power source is the weak point of AUVs, so it is a challenge for AUVs to exchange each vehicle smoothly before the energy capacity becomes empty or to extend the operating time of each vehicle.<br><br> | |||
The overview of the AUVs operation in the offshore platform is as below. The AUVs inspect the subsea structures such as pipelines automatically and they can communicate with the operators in the mothership through the transponders and satellites. | |||
[[File:AUV operation 2.png|800px|framelessthumb]]<br><br> | |||
The general arrangement of AUV's mechanical components is as below. Typical AUVs look like a submarine, and they have thrusters and power sources that are necessary to move in the water. In the water, the amount of air that can be used for the combustion of fuel is very few, so a battery or fuel cell is generally used as a power source of AUV. In addition, there are some sensors and communication systems such as sonar, camera, and acoustic system, and they are very important to move underwater automatically and inspect the subsea structures. | |||
[[File:Structure Urashima 1.png|800px|frameless]] | |||
==Design Structure Matrix (DSM) Allocation== | ==Design Structure Matrix (DSM) Allocation== | ||
[[File: | [[File:DSMrev.png|1000px|frameless]] | ||
<br><br> | |||
The above 2AUVOPI tree shows the relationship between some systems related to the AUV that uses the battery as a power source. This tree says that the AUV for offshore platform inspection (2AUVOPI) is one of the methods of the offshore platform inspection and consists of the vessel (3VES), thruster (3THR), power source (3POW), position sensing device (3PSD), communication device (3COD), and inspection device (3IND) subsystems. These subsystems require following components: composite (4COM), screw (4SCR), electric motor (4EMO), battery (4BAT), GPS antenna (4GPS), sonar (4SON), acoustic communication device (4ACD), camera (4CAM), inspection sensor (4INS). | |||
==Roadmap Model using OPM== | ==Roadmap Model using OPM== | ||
We provide an Object-Process-Diagram (OPD) of the '''2AUVOPI roadmap''' as below. As this diagram shows, the object of this roadmap (AUV) consists of subsystems such as thrusters, battery, controller, sonar, and sensor. These subsystems are organized for the movement in the water, the inspection of subsea structures, and the communication with other underwater vehicles. In addition, some indicators that characterize the performance of AUV are also shown in this diagram, and these indicators are some of the Figure of Merit (FOM). | |||
[[File:OPD of AUV.png|1000px|frameless]] | |||
An Object-Process-Language (OPL) description that is generated automatically is as below. The content of this OPL is the same as the above OPD. | |||
[[File:OPL AUV 1.png|1000px|frameless]] | |||
==Figures of Merit (FOMs)== | |||
For the oil & gas offshore platform operators, the inspection of subsea structures is very important in order to secure safety. However, a large amount of inspection cost loses profitability, so it is important to minimize the inspection cost by making the inspection efficient. As we mentioned in the above "roadmap overview" section, AUV is suitable for the subsea structure inspection because of its flexibility. '''In order to make the inspection effective and efficient, AUV has to move accurately in the sea, so the accuracy of position sensing is important.''' In addition, AUVs have the capacity limitation of power source, so it is necessary to replenish the energy source periodically. However, if the inspection is interrupted in every replenishment, the efficiency of inspection is greatly reduced, so '''it is important to achieve a "continuous inspection system".''' In order to achieve this "continuous inspection system", '''it is necessary to exchange each AUV smoothly for energy replenishment, so the simultaneous operation of several AUVs is the key technology.''' If this simultaneous operation becomes possible, as the below figure shows, when an AUV's battery is low, a replacement AUV can approach automatically and take over the mission smoothly. Furthermore, if we can reduce the number of AUVs that are necessary for the inspection as much as possible, the capital cost will decrease, so '''the extension of the operating hours of each AUV is also important.'''<br> | |||
[[File: | [[File:Continuous Inspection.png|800px|frameless]]<br><br> | ||
The below table is a list of typical FOMs related to the key issues ('''Position Sensing, Simultaneous Operation, and Extension of Operating Hours''') that we mentioned above.<br><br> | |||
The table | [[File:FOM list1.png|1000px|frameless]]<br><br> | ||
The below table shows the relationship between several FOMs related to the extension of the operating hours.<br><br> | |||
[[File:FOM relationship.png|800px|frameless]] | |||
| | |||
==Alignment with Company Strategic Drivers== | ==Alignment with Company Strategic Drivers== | ||
[[File:Objective 3.png|1000px|frameless]] | |||
| | |||
| | |||
==Positioning of Company vs. Competition== | ==Positioning of Company vs. Competition== | ||
source: https://www. | Improvement in the battery system is very crucial for AUVs. The improved energy density of the battery can increase the operating hours and hence the operating distance of the AUVs. The increased operating distance can also help with accomplishing particular tasks with comparatively fewer AUVs. Since the R&D projects of battery are very resource-intensive, we decided to partner with the battery producer like Panasonic, LG chem, etc for R&D in the improvement of the energy density of the battery.<br> | ||
We plotted the data of energy density of Li-ion batteries from different companies like Panasonic, LG Chem, AESC, etc. We envision reaching an energy density of 350 Wh/Kg by 2030 for batteries to improve the operating hour of AUVs. <br> | |||
[[File:Positioning of Company vs Competition AUV.png|1000px|frameless|.]] | |||
source: https://www.osti.gov/pages/servlets/purl/1561559 | |||
==Technical Model== | ==Technical Model== | ||
As we mentioned above, the power unit (Battery or Fuel Cell) is an example of an important component for AUVs, so we explain related technical models. | |||
[[File: | ===Battery=== | ||
The key FOM of the battery is the “Energy Density (u)”. In this section, we treat the theoretical energy density of the battery, and its technical equation is as below.<br> | |||
[[File:Equationbattery.png|400px|frameless|Sonar]]<br> | |||
Below is the normalized tornado chart that shows the sensitivity of each parameter to | Below is the normalized tornado chart that shows the sensitivity of each parameter to energy density.<br> | ||
[[File: | [[File:Battery sensitivity.png|400px|frameless|Sonar]]<br> | ||
As this chart shows, | As this chart shows, "E", "n", and "M" have almost the same sensitivity for the theoretical energy density of the battery. In order to increase the energy capacity, we should increase "E" and "n" or decrease "M". "E" is determined by the electric potential difference between cathode and anode, so if we select high electric potential material for cathode or low electric potential material for the anode, "E" will be improved. However, when "E" becomes larger than 4.2 [V], there is a problem that the electrolyte in the Li-ion battery is decomposed. In order to solve this problem, we should develop a new electrolyte that can withstand high voltage. In addition, if we increase "n" and decrease "M" by developing light material that contains a lot of Li-ion, theoretical energy density will improve. | ||
In any case, in order to improve the energy density of the battery, it is necessary to develop new materials. The development of new material needs a lot of resources and investment, so outsourcing will be one of the options for us. | |||
=== | ===Fuel Cell === | ||
One of the expected power | One of the expected power source of AUV is a fuel cell. If we want to increase the energy capacity of a fuel cell, it is necessary to increase the amount of hydrogen storage. However, the space capacity of AUV is limited, so increasing the pressure of the stored hydrogen, rather than making the dimension of the hydrogen tank larger, would be effective. The relationship between the hydrogen pressure and the tank dimension is below.<br> | ||
[[File:Dimension (Hydrogen Tank).png| | [[File:Dimension (Hydrogen Tank).png|700px|frameless]]<br> | ||
If we can’t change the overall dimension of the hydrogen tank because of the AUV's size limitation, the variables that can be changed are “σ” and “t” in order to increase the hydrogen capacity. Below is the normalized tornado chart that shows the sensitivity of “σ” and “t” to the maximum hydrogen pressure.<br> | If we can’t change the overall dimension of the hydrogen tank because of the AUV's size limitation, the variables that can be changed are “σ” and “t” in order to increase the hydrogen capacity. Below is the normalized tornado chart that shows the sensitivity of “σ” and “t” to the maximum hydrogen pressure.<br> | ||
[[File:Sensitivity (Hydrogen).png| | [[File:Sensitivity (Hydrogen).png|400px|frameless]]<br> | ||
As this chart shows, “σ” and “t” have the same sensitivity for maximum hydrogen pressure. However, if we increase “t”, this directly leads to increasing the hydrogen tank weight. In order to avoid weight increase, it is effective to increase“σ”by changing the material of the hydrogen tank. | As this chart shows, “σ” and “t” have the same sensitivity for maximum hydrogen pressure. However, if we increase “t”, this directly leads to increasing the hydrogen tank weight. In order to avoid weight increase, it is effective to increase“σ”by changing the material of the hydrogen tank. | ||
==Key Publications and Patents== | ==Key Publications and Patents== | ||
===Publications=== | ===Publications=== | ||
Title: '''S.G. Chappell, et al. "Acoustic communication between two autonomous underwater vehicles" IEEE Symposium on Autonomous Underwater Vehicle Technology (1994)''' <br> | |||
Executive Summary: This paper describes a project designed to investigate and demonstrate communication between two autonomous underwater vehicles (AUVs). This paper presents the results of in-water field experiments in which two AUV systems were able to communicate with each other using acoustic modems while conducting a simple mission. | |||
<br> | |||
[https://ieeexplore-ieee-org.libproxy.mit.edu/document/518661 Link]<br> | |||
Title: '''"A battery-free sensor for underwater exploration" MIT News (2019)''' <br> | |||
Executive Summary: This article talks about the battery-free underwater communication system that uses near-zero power to transmit sensor data developed by MIT researchers. The system makes use of two key phenomena. One, called the “piezoelectric effect,” occurs when vibrations in certain materials generate an electrical charge. The other is “backscatter,” a communication technique commonly used for RFID tags, that transmits data by reflecting modulated wireless signals off a tag and back to a reader. <br> | |||
We believe that technologies like this can completely revolutionize the AUVs capabilities. <br> | |||
[https://news.mit.edu/2019/battery-free-sensor-underwater-exploration-0820 Link]<br> | |||
Title: '''Bruno Scrosati, Jürgen Garche. "Lithium Batteries: Status, Prospects and Future" Journal of Power Sources (2010)''' <br> | |||
Executive Summary: This review focuses first on the present status of lithium battery technology, then on its near future development and finally it examines important new directions aimed at achieving quantum jumps in energy and power content. <br> | |||
[https://www.researchgate.net/publication/223709919_Lithium_Batteries_Status_Prospects_and_Future Link]<br> | |||
===Patents=== | ===Patents=== | ||
Title: '''Byrd, et al. (2019) "Underwater vehicle for inspection of a subsea structure in a body of water and related method"''' <br> | |||
Executive Summary: The invented AUV has a body like a torpedo and this AUV can sail safely at a certain distance from the pipelines. In addition, this AUV has 2 sensors on the upper and lower side of its body, and these sensors enable us to detect problems such as corrosion in the pipelines nondestructively. | |||
<br> | |||
[https://patents.google.com/patent/WO2016178045A1/en Link] | |||
Title: '''Ilia Vainstein, et al. (2004) "Wireless underwater communication system"''' <br> | |||
Executive Summary: This patent relates to a wireless underwater (UW) communications system for real-time transmission of video, control, and data-communications between underwater vehicles; or between an underwater vehicle and a surface platform; between underwater platforms; or the likes. | |||
<br> | |||
[https://patents.google.com/patent/WO2004049604A1/en?oq=communication+technology+between+AUVs Link] | |||
==List of R&D Projects== | ==List of R&D Projects== | ||
Line 92: | Line 111: | ||
In order to achieve a seamless inspection, it is important to communicate between each AUV and take over the mission smoothly, so '''the establishment of communication technology between AUVs is an important R&T topic'''. | In order to achieve a seamless inspection, it is important to communicate between each AUV and take over the mission smoothly, so '''the establishment of communication technology between AUVs is an important R&T topic'''. | ||
In addition, the longer the hours an AUV can operate per one mission, the more cost-effective it becomes because we can reduce the number of AUVs that are necessary to be deployed for replacement. | In addition, the longer the hours an AUV can operate per one mission, the more cost-effective it becomes because we can reduce the number of AUVs that are necessary to be deployed for replacement. | ||
Therefore, we think that '''the extension of AUV's operating hours is also an important R&T issue'''. | Therefore, we think that '''the extension of AUV's operating hours is also an important R&T issue'''.<br> | ||
By the way, the detection threshold of sonar is determined by the directivity of the receiver. We think that the improvement of the directivity is not an R&D issue but a matter of setting of the sonar equipment, so we excluded the sonar from the R&D list. | |||
<br> | <br> | ||
<br> | <br> | ||
<big>'''Communication technology between AUVs'''<br></big> | <big>'''Communication technology between AUVs'''<br></big> | ||
Currently, AUVs for oil and gas platform inspection are in practical use, but they are | Currently, AUVs for oil and gas platform inspection are in practical use, but they are operated independently.<ref>Kawasaki Heavy Industries, Autonomous Underwater Vehicle (AUV) “SPICE”, http://www.khisubsea.co.uk/autonomous-underwater-vehicle/</ref> | ||
In order to operate several AUVs simultaneously, acoustic multiplexing technology is necessary as a communication method. If we can achieve communication between at least 2 AUVs, we can automatically exchange an AUV with an empty battery for an AUV with a full battery in the deep sea. Based on this assumption, '''we set the establishment of the communication technology between 2 AUVs as our primary goal.''' | |||
Based on this | Based on the previous similar R&D projects of AUV's communication technology, we plan to take four years for this R&D project and estimate that our R&D cost of acoustic communication technology is 10 million $. This budget covers the design (1 million $), 2 prototype AUVs production (5 million $), field test (2 million $), and improvement (2 million $). Through this R&D, '''we will achieve the simultaneous operation of 2 AUVs in 2024.''' | ||
<br> | <br> | ||
<br> | <br> | ||
<big>'''Extension of AUV's operating hours'''<br></big> | <big>'''Extension of AUV's operating hours'''<br></big> | ||
The extension of AUV's operating hours will be achieved by the development of battery technology or fuel cell technology. | We focus on the establishment of a continuous inspection system, and it is possible to achieve this by only introducing communication technology as we mentioned above. However, if we can extend the operating hours, our AUV will be more competitive, so '''we set the extension of operating hours as our secondary goal.''' The extension of AUV's operating hours will be achieved by '''the development of battery technology or fuel cell technology.''' These technologies require a lot of resources, so it is difficult to build everything up from scratch. Fortunately, the technology competition between battery and fuel cell has been progressing in the automobile field, so we will be able to apply the result of R&D of the automotive. In our analysis, we think that both Li-ion battery and fuel cell are promising energy source for AUV at present. Based on the battery-powered and fuel-cell-powered AUVs that were built so far, we made model cases in 2020 and 2030 as follows. | ||
These technologies require a lot of resources, so it is difficult to build everything up from scratch. Fortunately, the technology competition between battery and fuel cell has been progressing in the automobile field, so we will be able to apply the result of R& | |||
In our analysis, we think that both Li-ion battery and fuel cell are promising energy source for AUV at present. | |||
Based on the battery-powered and fuel-cell-powered AUVs that were built so far, we made model cases in 2020 and 2030 as follows. | |||
<ref>Kawasaki Heavy Industries, https://www.khi.co.jp/stories/articles/vol99/</ref> | <ref>Kawasaki Heavy Industries, https://www.khi.co.jp/stories/articles/vol99/</ref> | ||
<ref>Toshio Maeda et al, Fuel Cell AUV "URASHIMA", Mitsubishi Heavy Industries, Ltd. Technical Review Vol.43 No.1(Jan.2006), https://www.mhi.co.jp/technology/review/pdf/e431/e431024.pdf</ref> | <ref>Toshio Maeda et al, Fuel Cell AUV "URASHIMA", Mitsubishi Heavy Industries, Ltd. Technical Review Vol.43 No.1(Jan.2006), https://www.mhi.co.jp/technology/review/pdf/e431/e431024.pdf</ref> | ||
<ref>Reinhardt Wagner, Battery Fuel Gauges: Accurately Measuring Charge Level (2006)</ref> | <ref>Reinhardt Wagner, Battery Fuel Gauges: Accurately Measuring Charge Level (2006)</ref> | ||
<ref>DOE, Target Explanation Document: Onboard Hydrogen Storage for Light-Duty Fuel Cell Vehicles (2017), https://www.energy.gov/sites/prod/files/2017/05/f34/fcto_targets_onboard_hydro_storage_explanation.pdf</ref> | <ref>DOE, Target Explanation Document: Onboard Hydrogen Storage for Light-Duty Fuel Cell Vehicles (2017), https://www.energy.gov/sites/prod/files/2017/05/f34/fcto_targets_onboard_hydro_storage_explanation.pdf</ref> | ||
[[File:Model Case | [[File:Model Case 2.png|500px|frameless]]<br> | ||
At present, the performance of battery and fuel cell are in competition (Battery (313.6(km/week)) VS Fuel Cell (294.0(km/week))). In addition, the performance improvement expected in 2030 is also in competition (Battery ( | At present, the performance of battery and fuel cell are in competition (Battery (313.6(km/week)) VS Fuel Cell (294.0(km/week))). In addition, the performance improvement expected in 2030 is also in competition (Battery (411.6(km/week)) VS Fuel Cell (417.8(km/week))). Therefore, we think that narrowing down power unit candidates to either battery or fuel cell is not a good idea at this time. However, these predictions are just model cases, so the situation may change significantly depending on future technological developments. Therefore, we think that it would be better to decide which technology is suitable for our AUV later. '''We plan to evaluate in 2025 whether we should invest to the R&D of new power unit or not and which technology is suitable for our AUVs.''' If we decide to invest in R&D, we will take five years for this R&D. In order to save money, we will divert 2 prototype AUVs which are manufactured for communication technology testing. '''We estimate that the R&D of the power unit will cost 8 million $.''' This budget covers the design (2 million $), 2 prototype power units production (2 million $), field test (2 million $), and improvement (2 million $). Through this R&D, '''we will be able to extend operating hour almost double and operating distance by around 30% in 2030.''' | ||
However, these predictions are just model cases, so the situation may change significantly depending on future technological developments. | |||
Therefore, '''we | |||
<br> | <br> | ||
<br> | <br> | ||
Line 126: | Line 139: | ||
==Financial Model== | ==Financial Model== | ||
Based on the above R&T schedule, we analyzed the financial feasibility of our project. | Based on the above R&T schedule, we analyzed the financial feasibility of our project. | ||
As we mentioned above, our strategy has two stages. In the first stage, we conduct R&D of acoustic communication technology and start selling AUVs with this technology in 2025. | |||
In the second stage, we conduct R& | In the second stage, we conduct R&D of battery or fuel cell technology and start selling AUVs with new power units in 2031. | ||
In addition to these two options, we set the base case that we don't invest in any R&D project, we analyzed the three options.<br> | |||
In | '''1) Base model''': In this model, we don't invest in any R&D project. In this case, our AUV can't provide a continuous inspection system, so the unit price will be low and the number of sales will be also small (0.5 million$/unit, 4 unit/year) because of the low competitiveness<br><br> | ||
'''2) Conservative model''': We invest in the R&D of communication technology but don't invest in the R&D of the power unit. We will continue to sell AUVs with only acoustic communication technology. In this case, the operation hours of this AUV remain short, so the unit price and the number of sales will be middle (1 million$/unit, 10 unit/year) based on the middle competitiveness.<br><br> | |||
'''3) Optimistic model:''' We decide to invest in the R&D of the power unit, and we will start selling the AUVs with new power units in 2031. In this case, the operation hours of this new AUV will be long, so the unit price and the number of sales will increase (1.2 million$/unit, 20 unit/year) based on the high competitiveness.<br><br> | |||
As we mentioned in the "List of R&D Projects" section, we assume that the R&D cost of the communication technology is 10 million $, and the R&D cost of the power unit is 8 million $. In each model, we expect a learning effect on productivity. We assume that the initial profit margin is 20%, and the profit margin improves by 1% each year. Furthermore, we assume that the discount rate is 7% that is general in the R&D project, and calculate the Net Present Value (NPV) by 2040. Based on these assumptions, we analyzed the financial forecast as follows.<br> | |||
[[File: | <big>'''Financial forecast of Base model'''</big><br> | ||
[[File:Base.png|1000px|frameless|]] | |||
<big>'''Financial forecast of | <big>'''Financial forecast of conservative model'''</big><br> | ||
[[File:Conservative.png|1000px|frameless|]] | |||
[[File: | <big>'''Financial forecast of optimistic model'''</big><br> | ||
[[File:Opt model.png|1000px|frameless|]] | |||
As these results show, | As these results show, in the base model, the NPV is positive (6.2 million $), but the profitability of our project is low. If we choose the conservative model, the NPV is positive (11.1 million $), and this is much larger than the base model. This means that we can increase our profitability through R&D. In addition, the optimistic model is more profitable (NPV: 16.7 million $), so it can be said that the stage-gate related to the power unit scheduled in 2025 is very important for our project because this will determine whether we can maximize profits or not. | ||
==Technology Strategy Statement== | ==Technology Strategy Statement== | ||
As we mentioned above, our goal is the establishment of an | As we mentioned above, our goal is the establishment of an efficient continuous inspection system for oil and gas offshore platforms. In order to achieve this goal, we plan to invest in two R&D projects. The first is the integration of acoustic multiplexing technology with AUVs. We will invest 10 million $ and plan to succeed in the communication between 2 AUVs in 2024. If we succeed in this R&D, we can start selling the continuous inspection system in 2025. The second is the development of a new power unit. If we can make the operating hours of our AUV double by introducing a new power unit, our AUVs will be more competitive. Our strategy is to convert the power unit technology in the automobile field into our AUVs, and we will evaluate the possibility of a new power unit in 2025. If we decide to invest in this R&D, we will invest 8 million $. Through this R&D, we will be able to make the operating hours double and increase the operating distance by 30% in 2030, so we can provide a more efficient continuous inspection system for offshore platform operators. | ||
In order to achieve this goal, we | |||
The first is the integration of acoustic multiplexing technology with AUVs | |||
The second | |||
[[File:Roadmap swoosh | [[File:Roadmap swoosh chart1.png|800px|frameless]]<br> | ||
==References== | ==References== | ||
<references /> | <references /> |
Latest revision as of 17:01, 3 December 2020
Technology Roadmap Sections and Deliverables
The unique identifier of this technology roadmap is:
- 2AUVOPI - Autonomous Underwater Vehicle for Offshore Platform Inspection
This indicates that we are dealing with a “level 2” roadmap at the product or system level, where “level 1” would indicate a market level roadmap and “level 3” or “level 4” would indicate an individual technology roadmap.
Roadmap Overview
The offshore platforms are the oil and gas production facilities that are located offshore. In the past, oil and gas were generally produced on the ground. However, as the number of fossil fuel-rich sites that were accessible from the ground has been limited, offshore oil and gas development has been important. In 2016, there were more than 3,000 offshore oil and gas production facilities in the world, and it is estimated that the number of facilities will increase.<ref>International Energy Agency (IEA), Offshore Energy Outlook (2018), https://webstore.iea.org/download/direct/1034</ref>
The offshore platform has a lot of subsea structures such as pipelines, so the inspection and maintenance of these structures is a very important issue. However, some platforms are installed in water depths of more than hundreds of meters, so it is impossible for humans to dive and inspect these structures. In order to overcome this problem, Remotely Operated Vehicles (ROVs) are widely used. ROVs are unmanned vehicles that are connected to the mothership by a wire and can be manipulated by operators who are boarding in the mothership. In addition, ROVs can get power through the wire, so they can be operated for a long time. However, ROVs have many problems such as motion limitation caused by the wire.
On the other hand, the Autonomous Underwater Vehicles (AUVs) don't have wires, so the operation flexibility is the great advantage of AUVs. In order to take advantage of this strength of flexibility, securing the accuracy of position sensing is important for AUVs. Meanwhile, the capacity limit of the power source is the weak point of AUVs, so it is a challenge for AUVs to exchange each vehicle smoothly before the energy capacity becomes empty or to extend the operating time of each vehicle.
The overview of the AUVs operation in the offshore platform is as below. The AUVs inspect the subsea structures such as pipelines automatically and they can communicate with the operators in the mothership through the transponders and satellites.
The general arrangement of AUV's mechanical components is as below. Typical AUVs look like a submarine, and they have thrusters and power sources that are necessary to move in the water. In the water, the amount of air that can be used for the combustion of fuel is very few, so a battery or fuel cell is generally used as a power source of AUV. In addition, there are some sensors and communication systems such as sonar, camera, and acoustic system, and they are very important to move underwater automatically and inspect the subsea structures.
Design Structure Matrix (DSM) Allocation
The above 2AUVOPI tree shows the relationship between some systems related to the AUV that uses the battery as a power source. This tree says that the AUV for offshore platform inspection (2AUVOPI) is one of the methods of the offshore platform inspection and consists of the vessel (3VES), thruster (3THR), power source (3POW), position sensing device (3PSD), communication device (3COD), and inspection device (3IND) subsystems. These subsystems require following components: composite (4COM), screw (4SCR), electric motor (4EMO), battery (4BAT), GPS antenna (4GPS), sonar (4SON), acoustic communication device (4ACD), camera (4CAM), inspection sensor (4INS).
Roadmap Model using OPM
We provide an Object-Process-Diagram (OPD) of the 2AUVOPI roadmap as below. As this diagram shows, the object of this roadmap (AUV) consists of subsystems such as thrusters, battery, controller, sonar, and sensor. These subsystems are organized for the movement in the water, the inspection of subsea structures, and the communication with other underwater vehicles. In addition, some indicators that characterize the performance of AUV are also shown in this diagram, and these indicators are some of the Figure of Merit (FOM).
An Object-Process-Language (OPL) description that is generated automatically is as below. The content of this OPL is the same as the above OPD.
Figures of Merit (FOMs)
For the oil & gas offshore platform operators, the inspection of subsea structures is very important in order to secure safety. However, a large amount of inspection cost loses profitability, so it is important to minimize the inspection cost by making the inspection efficient. As we mentioned in the above "roadmap overview" section, AUV is suitable for the subsea structure inspection because of its flexibility. In order to make the inspection effective and efficient, AUV has to move accurately in the sea, so the accuracy of position sensing is important. In addition, AUVs have the capacity limitation of power source, so it is necessary to replenish the energy source periodically. However, if the inspection is interrupted in every replenishment, the efficiency of inspection is greatly reduced, so it is important to achieve a "continuous inspection system". In order to achieve this "continuous inspection system", it is necessary to exchange each AUV smoothly for energy replenishment, so the simultaneous operation of several AUVs is the key technology. If this simultaneous operation becomes possible, as the below figure shows, when an AUV's battery is low, a replacement AUV can approach automatically and take over the mission smoothly. Furthermore, if we can reduce the number of AUVs that are necessary for the inspection as much as possible, the capital cost will decrease, so the extension of the operating hours of each AUV is also important.
The below table is a list of typical FOMs related to the key issues (Position Sensing, Simultaneous Operation, and Extension of Operating Hours) that we mentioned above.
The below table shows the relationship between several FOMs related to the extension of the operating hours.
Alignment with Company Strategic Drivers
Positioning of Company vs. Competition
Improvement in the battery system is very crucial for AUVs. The improved energy density of the battery can increase the operating hours and hence the operating distance of the AUVs. The increased operating distance can also help with accomplishing particular tasks with comparatively fewer AUVs. Since the R&D projects of battery are very resource-intensive, we decided to partner with the battery producer like Panasonic, LG chem, etc for R&D in the improvement of the energy density of the battery.
We plotted the data of energy density of Li-ion batteries from different companies like Panasonic, LG Chem, AESC, etc. We envision reaching an energy density of 350 Wh/Kg by 2030 for batteries to improve the operating hour of AUVs.
source: https://www.osti.gov/pages/servlets/purl/1561559
Technical Model
As we mentioned above, the power unit (Battery or Fuel Cell) is an example of an important component for AUVs, so we explain related technical models.
Battery
The key FOM of the battery is the “Energy Density (u)”. In this section, we treat the theoretical energy density of the battery, and its technical equation is as below.
Below is the normalized tornado chart that shows the sensitivity of each parameter to energy density.
As this chart shows, "E", "n", and "M" have almost the same sensitivity for the theoretical energy density of the battery. In order to increase the energy capacity, we should increase "E" and "n" or decrease "M". "E" is determined by the electric potential difference between cathode and anode, so if we select high electric potential material for cathode or low electric potential material for the anode, "E" will be improved. However, when "E" becomes larger than 4.2 [V], there is a problem that the electrolyte in the Li-ion battery is decomposed. In order to solve this problem, we should develop a new electrolyte that can withstand high voltage. In addition, if we increase "n" and decrease "M" by developing light material that contains a lot of Li-ion, theoretical energy density will improve. In any case, in order to improve the energy density of the battery, it is necessary to develop new materials. The development of new material needs a lot of resources and investment, so outsourcing will be one of the options for us.
Fuel Cell
One of the expected power source of AUV is a fuel cell. If we want to increase the energy capacity of a fuel cell, it is necessary to increase the amount of hydrogen storage. However, the space capacity of AUV is limited, so increasing the pressure of the stored hydrogen, rather than making the dimension of the hydrogen tank larger, would be effective. The relationship between the hydrogen pressure and the tank dimension is below.
If we can’t change the overall dimension of the hydrogen tank because of the AUV's size limitation, the variables that can be changed are “σ” and “t” in order to increase the hydrogen capacity. Below is the normalized tornado chart that shows the sensitivity of “σ” and “t” to the maximum hydrogen pressure.
As this chart shows, “σ” and “t” have the same sensitivity for maximum hydrogen pressure. However, if we increase “t”, this directly leads to increasing the hydrogen tank weight. In order to avoid weight increase, it is effective to increase“σ”by changing the material of the hydrogen tank.
Key Publications and Patents
Publications
Title: S.G. Chappell, et al. "Acoustic communication between two autonomous underwater vehicles" IEEE Symposium on Autonomous Underwater Vehicle Technology (1994)
Executive Summary: This paper describes a project designed to investigate and demonstrate communication between two autonomous underwater vehicles (AUVs). This paper presents the results of in-water field experiments in which two AUV systems were able to communicate with each other using acoustic modems while conducting a simple mission.
Link
Title: "A battery-free sensor for underwater exploration" MIT News (2019)
Executive Summary: This article talks about the battery-free underwater communication system that uses near-zero power to transmit sensor data developed by MIT researchers. The system makes use of two key phenomena. One, called the “piezoelectric effect,” occurs when vibrations in certain materials generate an electrical charge. The other is “backscatter,” a communication technique commonly used for RFID tags, that transmits data by reflecting modulated wireless signals off a tag and back to a reader.
We believe that technologies like this can completely revolutionize the AUVs capabilities.
Link
Title: Bruno Scrosati, Jürgen Garche. "Lithium Batteries: Status, Prospects and Future" Journal of Power Sources (2010)
Executive Summary: This review focuses first on the present status of lithium battery technology, then on its near future development and finally it examines important new directions aimed at achieving quantum jumps in energy and power content.
Link
Patents
Title: Byrd, et al. (2019) "Underwater vehicle for inspection of a subsea structure in a body of water and related method"
Executive Summary: The invented AUV has a body like a torpedo and this AUV can sail safely at a certain distance from the pipelines. In addition, this AUV has 2 sensors on the upper and lower side of its body, and these sensors enable us to detect problems such as corrosion in the pipelines nondestructively.
Link
Title: Ilia Vainstein, et al. (2004) "Wireless underwater communication system"
Executive Summary: This patent relates to a wireless underwater (UW) communications system for real-time transmission of video, control, and data-communications between underwater vehicles; or between an underwater vehicle and a surface platform; between underwater platforms; or the likes.
Link
List of R&D Projects
Summary
Our goal is the establishment of an AUV system for continuous inspection of oil and gas offshore platforms. This will be able to contribute to providing efficient inspections and making platforms safe.
However, because the energy capacity of each AUV is limited, it is necessary to put the multiple AUVs into the mission by turns.
In order to achieve a seamless inspection, it is important to communicate between each AUV and take over the mission smoothly, so the establishment of communication technology between AUVs is an important R&T topic.
In addition, the longer the hours an AUV can operate per one mission, the more cost-effective it becomes because we can reduce the number of AUVs that are necessary to be deployed for replacement.
Therefore, we think that the extension of AUV's operating hours is also an important R&T issue.
By the way, the detection threshold of sonar is determined by the directivity of the receiver. We think that the improvement of the directivity is not an R&D issue but a matter of setting of the sonar equipment, so we excluded the sonar from the R&D list.
Communication technology between AUVs
Currently, AUVs for oil and gas platform inspection are in practical use, but they are operated independently.<ref>Kawasaki Heavy Industries, Autonomous Underwater Vehicle (AUV) “SPICE”, http://www.khisubsea.co.uk/autonomous-underwater-vehicle/</ref>
In order to operate several AUVs simultaneously, acoustic multiplexing technology is necessary as a communication method. If we can achieve communication between at least 2 AUVs, we can automatically exchange an AUV with an empty battery for an AUV with a full battery in the deep sea. Based on this assumption, we set the establishment of the communication technology between 2 AUVs as our primary goal.
Based on the previous similar R&D projects of AUV's communication technology, we plan to take four years for this R&D project and estimate that our R&D cost of acoustic communication technology is 10 million $. This budget covers the design (1 million $), 2 prototype AUVs production (5 million $), field test (2 million $), and improvement (2 million $). Through this R&D, we will achieve the simultaneous operation of 2 AUVs in 2024.
Extension of AUV's operating hours
We focus on the establishment of a continuous inspection system, and it is possible to achieve this by only introducing communication technology as we mentioned above. However, if we can extend the operating hours, our AUV will be more competitive, so we set the extension of operating hours as our secondary goal. The extension of AUV's operating hours will be achieved by the development of battery technology or fuel cell technology. These technologies require a lot of resources, so it is difficult to build everything up from scratch. Fortunately, the technology competition between battery and fuel cell has been progressing in the automobile field, so we will be able to apply the result of R&D of the automotive. In our analysis, we think that both Li-ion battery and fuel cell are promising energy source for AUV at present. Based on the battery-powered and fuel-cell-powered AUVs that were built so far, we made model cases in 2020 and 2030 as follows.
<ref>Kawasaki Heavy Industries, https://www.khi.co.jp/stories/articles/vol99/</ref>
<ref>Toshio Maeda et al, Fuel Cell AUV "URASHIMA", Mitsubishi Heavy Industries, Ltd. Technical Review Vol.43 No.1(Jan.2006), https://www.mhi.co.jp/technology/review/pdf/e431/e431024.pdf</ref>
<ref>Reinhardt Wagner, Battery Fuel Gauges: Accurately Measuring Charge Level (2006)</ref>
<ref>DOE, Target Explanation Document: Onboard Hydrogen Storage for Light-Duty Fuel Cell Vehicles (2017), https://www.energy.gov/sites/prod/files/2017/05/f34/fcto_targets_onboard_hydro_storage_explanation.pdf</ref>
At present, the performance of battery and fuel cell are in competition (Battery (313.6(km/week)) VS Fuel Cell (294.0(km/week))). In addition, the performance improvement expected in 2030 is also in competition (Battery (411.6(km/week)) VS Fuel Cell (417.8(km/week))). Therefore, we think that narrowing down power unit candidates to either battery or fuel cell is not a good idea at this time. However, these predictions are just model cases, so the situation may change significantly depending on future technological developments. Therefore, we think that it would be better to decide which technology is suitable for our AUV later. We plan to evaluate in 2025 whether we should invest to the R&D of new power unit or not and which technology is suitable for our AUVs. If we decide to invest in R&D, we will take five years for this R&D. In order to save money, we will divert 2 prototype AUVs which are manufactured for communication technology testing. We estimate that the R&D of the power unit will cost 8 million $. This budget covers the design (2 million $), 2 prototype power units production (2 million $), field test (2 million $), and improvement (2 million $). Through this R&D, we will be able to extend operating hour almost double and operating distance by around 30% in 2030.
R&T schedule
The overall R&T schedule is as below. We set a stage-gate in 2025 and are going to decide whether we should expand our project or not.
Financial Model
Based on the above R&T schedule, we analyzed the financial feasibility of our project.
As we mentioned above, our strategy has two stages. In the first stage, we conduct R&D of acoustic communication technology and start selling AUVs with this technology in 2025.
In the second stage, we conduct R&D of battery or fuel cell technology and start selling AUVs with new power units in 2031.
In addition to these two options, we set the base case that we don't invest in any R&D project, we analyzed the three options.
1) Base model: In this model, we don't invest in any R&D project. In this case, our AUV can't provide a continuous inspection system, so the unit price will be low and the number of sales will be also small (0.5 million$/unit, 4 unit/year) because of the low competitiveness
2) Conservative model: We invest in the R&D of communication technology but don't invest in the R&D of the power unit. We will continue to sell AUVs with only acoustic communication technology. In this case, the operation hours of this AUV remain short, so the unit price and the number of sales will be middle (1 million$/unit, 10 unit/year) based on the middle competitiveness.
3) Optimistic model: We decide to invest in the R&D of the power unit, and we will start selling the AUVs with new power units in 2031. In this case, the operation hours of this new AUV will be long, so the unit price and the number of sales will increase (1.2 million$/unit, 20 unit/year) based on the high competitiveness.
As we mentioned in the "List of R&D Projects" section, we assume that the R&D cost of the communication technology is 10 million $, and the R&D cost of the power unit is 8 million $. In each model, we expect a learning effect on productivity. We assume that the initial profit margin is 20%, and the profit margin improves by 1% each year. Furthermore, we assume that the discount rate is 7% that is general in the R&D project, and calculate the Net Present Value (NPV) by 2040. Based on these assumptions, we analyzed the financial forecast as follows.
Financial forecast of Base model
Financial forecast of conservative model
Financial forecast of optimistic model
As these results show, in the base model, the NPV is positive (6.2 million $), but the profitability of our project is low. If we choose the conservative model, the NPV is positive (11.1 million $), and this is much larger than the base model. This means that we can increase our profitability through R&D. In addition, the optimistic model is more profitable (NPV: 16.7 million $), so it can be said that the stage-gate related to the power unit scheduled in 2025 is very important for our project because this will determine whether we can maximize profits or not.
Technology Strategy Statement
As we mentioned above, our goal is the establishment of an efficient continuous inspection system for oil and gas offshore platforms. In order to achieve this goal, we plan to invest in two R&D projects. The first is the integration of acoustic multiplexing technology with AUVs. We will invest 10 million $ and plan to succeed in the communication between 2 AUVs in 2024. If we succeed in this R&D, we can start selling the continuous inspection system in 2025. The second is the development of a new power unit. If we can make the operating hours of our AUV double by introducing a new power unit, our AUVs will be more competitive. Our strategy is to convert the power unit technology in the automobile field into our AUVs, and we will evaluate the possibility of a new power unit in 2025. If we decide to invest in this R&D, we will invest 8 million $. Through this R&D, we will be able to make the operating hours double and increase the operating distance by 30% in 2030, so we can provide a more efficient continuous inspection system for offshore platform operators.
References
<references />